Metal Laser Cutter

40W 50W CO2 Laser Power Supply for CO2 Laser Engraver Cutter MYJG-50 110V / 220V

40W 50W CO2 Laser Power Supply for CO2 Laser Engraver Cutter MYJG-50 110V / 220V
40W 50W CO2 Laser Power Supply for CO2 Laser Engraver Cutter MYJG-50 110V / 220V
40W 50W CO2 Laser Power Supply for CO2 Laser Engraver Cutter MYJG-50 110V / 220V
40W 50W CO2 Laser Power Supply for CO2 Laser Engraver Cutter MYJG-50 110V / 220V
40W 50W CO2 Laser Power Supply for CO2 Laser Engraver Cutter MYJG-50 110V / 220V

40W 50W CO2 Laser Power Supply for CO2 Laser Engraver Cutter MYJG-50 110V / 220V

The best price for the best products. Ltd offers faster and better services with less price! 40W 50W CO2 Laser Power Supply for CO2 Laser Engraver Cutter MYJG-50 110V / 220V.

Brand New, High Quality and Extra Long Life. Good compatibility: it can be applicable to 50W laser tube manufactured by various factories.

Quick response speed and effect, high performance, large cutting power, it also can prolong laser tube service life. Easy control: the start and stop of laser can be easily controlled by TTL level.

The power supply has output open circuit protection. The power supply has TTL signal indication, water through signal indication and laser output indication. This power supply has the Buttonto test output laser manually.

Application: Sculpture and cut acrylic, fabric, double color sheet and rubber etc. Laser Tube connection:(Refer to Power supply and laser Device's connection Diagram)High voltage terminal of HY-T60 power supply should be connected to the positive pole of CO2 laser device. Current circuit of the power supply shall be connected to negative pole(laser output terminal)of laser device, through an ampere meter or directly. Connection of control signal(Refer to Power supply and control board's connection Diagram)The control signal shall be reliably connected to control terminal of the power supply HY-T60, after connecting the DAC output signal and TTL signal of external computer with the power supply, the laser device shall work as expected.

If the laser lamp can not work properly, should check the control signal whether correct or not(include check the voltage specification and logic), if use PWM control as power control, make sure f greater than or equal to 20KHz, Amplitude(peak value)less than or equal to 5V, Check and protection switch WP connection is correct at same time. Voltage of power input: HY-T60's power input of the power supply shall be 220VAC/50Hz. If 110VAC required please specify when placing order. Others: A group of protection switches are also reserved for detection of water switch, fan switch, open-enclosure protection and so on.

Switch Light Control, High Level(greater than or equal to 3V)-Bright dipping, Low Level(less than or equal to 0.3V)-No Light Dipping. High Level-No light Dipping, Low Level(less than or equal to 0.3V)-Bright Dipping. Switch Light Control, High Level(greater than or equal to 3V)- No light Dipping, Low Level(less than or equal to 0.3V)-Bright Dipping. The foot must connected with laser machine's enclosure and ground properly. Laser Power supply control terminal can use 0-5V Analog Signal Control, also can use 5V PWM Signal to Control.

5V, Max output Current 20mA. Return must in original package and not been used.

This item is in the category "Business & Industrial\Printing & Graphic Arts\Screen & Specialty Printing\Engraving". The seller is "cnsigntech" and is located in this country: CN. This item can be shipped worldwide.

  • Material: Metal
  • Power: 50 W
  • Engraving Method: Laser
  • Brand: MCWlaser
  • Model: MYJG-50


40W 50W CO2 Laser Power Supply for CO2 Laser Engraver Cutter MYJG-50 110V / 220V